Compaq Polymer Tee connector has been designed to facilitate Loop-In & Loop-Out connection for HT AB Cable lines. Installation can be made quickly & easily in the field by giving connection which is simple of bolted type. The Compaq Tap-Off (TEE) allows complete Insulation of connections so that No bare Conductors are exposed.
• CPRI Tested and meets the Requirement of IEC 61109.
• Suitable Aluminium Busbar Confirming to IS/IEC.
• Simple and Easy Installation.
• High Creepage Polymer Insulator
Compaq rain sheds are used to increase the surface creepage distance of the cores of cable termination without increasing the tail length. They are also used to avoid continuity during rainy season to avoid short circuiting of the electrical network.
The rain sheds are made from high quality cross linked polyolefin material that offers exceptional non tracking behavior, insulation and long term service reliability for indoor and outdoor applications. The creepage extension sheds are internally coated with water resistant mastic.
|Shrink Temp. (deg. Celsius)||100|
Compaq Anti Tracking Cable Breakout provide permanent environmental seal to the crutch of 3 core PVR PILC cable rate upto 36KV.Compaq Anti Tracking breakout manufactured from high quality non tracking cross linked polyolefin material that offers exceptional insulation and long term service reliability.
· The breakouts are internally coated with water resistant mastic
· Excellent weather / UV resistance
· Good resistance to chemical, solvent, corrosion and fungus High dielectric strength
|Voltage (V)||11 kb|
Copper Mesh for rodent exclusions and rodent-proofing. Copper Mesh is tubular, laid flat, and rolled for easy storage and use. Great when used in combination with Todol closed-cell, expanding foam.
|Shrink Temp. (deg. Celsius)||100|
EPDM Cold shrink tubes are Tubular rubber sleeves which are factory expanded and assembled onto removable core. The core is removed after the tube has been positioned for installation over an in connection, the cold shrink tubing shrink and form a water proof seal. These sizes will cover a range of 1000 volt cables, copper and aluminum conductors. It is in Black color.
· Provides water tight seal upon recovery.
· Excellent mechanical strength.
· Application procedure is quick, simple & clean.
· Covered with thermochromatic paint that change colure upon achieving correct shrink temperature.
Medium Voltage Cold Applied Silicone Rubber bushing boot are used on screened or rubber insulated cables of 7.2 to 17.5 kV. Cold applied bushing boot is designed for use on either single or three core cables from 35 up to 400mm2, up to a maximum system voltage of 17.5 kV. The Bushing Boot can accommodate bushings with diameters between 30-70 mm.
Compaq System now offer our own universal medium voltage cold applied bushing protection boot for switchgear and transformer. Manufactured from high grade silicone with excellent non tracking and erosion resistance, the boot is very flexible and just one size covers right angle or straight connections for cable size 35-400mm2.
Medium Voltage Cold applied angle are used on indoor terminations of power cables maximum rated 17.5kV, XLPE, EPR, paper insulation cable with aluminium or copper conductor. These cold applied angle boots are used in switchgear and transformers cable end boxes, in which the cores of the cables are terminated vertically from below and are connected to bushing fixed there in. these boots are designed for use on either single or three core cable from 35sq mm to 400 sq mm. the bushing boots can accommodate bushing with diameter between 31-70mm.
· No special tools required
· No heating or filling required
· Suitable for vertical or angled position
· High interface pressure ensures absolute water tightness
Compaq heat shrink wraparound sleeves are manufactured from thermally stabilized cross-linked polyolefin, with a hot melt adhesive liner on the inner side of the sleeves. Upon heating, the sleeve shrinks and the adhesive melts, creating a water tight bond between the sleeve and cable sheath or cable Joint assembly components. CRS wraparound sleeve meat & even exceed the various national & international quality standards applicable. A corrosion proof stainless steel channel is used to close the sleeve during installation.
Compaq heat shrinkable wraparound sleeves are designed to repair damaged cable sheath. It is also suitable for use for rejecting of cable Joints and as additional corrosion protection on undamaged cables.
Quick & easy to apply, it provides maximum protection against correction & waterproof.
Compaq Double Layer Heat Shrinkable Tubing inner layer is made from insulation material to provide high insulation and the outer layer is made from semi-conductive materials to provide electric shielding. The tubing is manufactured with technology very suitable for applications in power cable joints up to 36kV.
Compaq Heat Shrink Right Angle/Straight boots are providing insulation to the bushings in the cable termination box, where the clearance between phase to phase and phase to earth is less than the normal air clearance. These boots provide protection against flashover in the event of high humidity, rodent menace and surge impulse. The boots are made from high quality cross linked non tracking polyolefin material. They are internally coated with water resistant red mastic.
· Excellent insulation, flame retardant, thermal stability, etc.
· Used to protect cable against flashover or surges induce in switchgear and transformer
· Shaped components to meet a range of requirements
· Continuous operation temperature: -550C to 1000C